芒果视频

一、光纖熔接機怎么用

首先剝開光纜，并將光纜固定到盤纖架上，將剝開后的光纖分別穿過熱縮管；然后打開熔接機電源，要根據不同的光纖類型選擇合適的熔接方式；接著制備光纖端面，將光纖放在熔接機的V型槽中，小心壓上光纖壓板和光纖夾具，要根據光纖切割長度設置光纖在壓板中的位置，并正確地放入防風罩中；接續光纖后取出光纖并用加熱器加固光纖熔接點，最后盤纖并固定即可。

二、光纖熔接機原理

光纖熔接機進行熔接，主要遵循三個原理：熔接的基本原理，對準原理（PAS制），估算損耗原理。當平行光從側面照射到光纖上時，由于光纖產生折射，通過物鏡被聚焦到電荷耦合器上，得到模擬視頻信號，再通過模/數轉換電路，變為數字信號。通過熔接機內的微處理器對圖像進行處理和識別，從而可以直觀顯示纖芯和包層的對準情況。電極預放電清潔光纖端面，電極放電使對接光纖的端面熔化，利用石英分子問的作用力使光纖連接起來。

三、光纖熔接機參數教程

光纖熔接機的主要參數有適用光纖芯數、熔接時間、加熱時間、熔接損耗、電池供電、操作環境、機器大小、光纖放大倍數等，不同的參數有不同的作用，例如加熱時間越短越好，通常設置在20秒左右，電池供電容量越大越好等。

四、光纖熔接機維修教程

光纖熔接機常見故障有開啟光纖熔接機開關后屏幕無光亮，且打開防風罩后發現電極座上的水平照明不亮，更換電源插座或保險絲即可；光纖能進行正常復位，進行間隙設置時屏幕變暗，沒有光纖圖象，且屏幕顯示停止在“設置間隙”，檢查并確認防風罩是否壓到位或簧片是否接觸良好即可。一般劣質光纖熔接機容易出故障，因此建議選購優質光纖熔接機品牌生產的產品。