一、電線中間接線怎么剝皮

電線從中間剝皮要用剝線鉗。使用要點：要根據導線直徑，選用剝線鉗刀片的孔徑。它是內線電工、電動機修理、儀器儀表電工常用的工具之一，用來供電工剝除電線頭部的表面絕緣層。剝線鉗可以使得電線被切斷的絕緣皮與電線分開，還可以防止觸電。

1、根據纜線的粗細型號，選擇相應的剝線刀口。將準備好的電纜放在剝線工具的刀刃中間，選擇好要剝線的長度。

2、握住剝線工具手柄，將電纜夾住，緩緩用力使電纜外表皮慢慢剝落。松開工具手柄，取出電纜線，這時電纜金屬整齊露出外面，其余絕緣塑料完好無損。

3、常用的話可以用上面的兩種剝線鉗，偶爾用的話也可以用電工刀、刀片、剪刀等，會操作的話，削不到里面的銅芯，其實削一點也沒關系。還有用打火機燒一下也行的。

二、剝線鉗怎么調節松緊

1、把需要剝線皮的電線剪平。

2、調好要剝皮的長度。

3、把線材接入鉗口。

4、用力按壓鉗柄，把鉗口中的線材的線皮剝去。

5、用力按壓鉗柄，把鉗口中的線材的線皮剝去。

6、如果剝線口的壓力過大，可以將壓力調小，否則容易把線壓斷。這個螺絲順時針調時將壓力調大，逆時針時將壓力調小。