一、恒溫振蕩器的溫度可以設置到幾度

恒溫振蕩器的溫度范圍：0~50度。

恒溫振蕩器的種類有用空氣恒溫的氣浴恒溫振蕩器、用水恒溫的水浴恒溫振蕩器和0℃至50℃的全溫恒溫振蕩器，其產品可用于植物、生物、微生物、遺傳、病毒、環保、食品、石油、化工等各類生物的精密培養、基因工程的研究。

二、恒溫振蕩器的溫度及各參數設定方法是什么

開機后，系統進入主監控畫面，按“停止/運行”鍵5秒啟動運行或停止運行，按“查詢/移位”鍵查詢設定值。在主界面按“設定”鍵，進入菜單，通過方向鍵選擇“運行參數”后按“設定”鍵進入編輯界面，每修改好一個參數后自動切換到下一個參數，若工作組設置為該組時將按照該工作組運行，按當前段時間設為0時表示后一段程序，退出編輯。白天黑夜模式時固定為兩段結束。第二段設為0表示該組為定值運行模式。長按“設定”鍵返回主監控畫面。用戶參數、溫度參數、系統參數設置在菜單界面選擇相應目錄，按“設定”鍵進入，系統參數需錄入密碼。

恒溫振蕩器能適應絕大多數控制系統，只有控制效果特別不理想時萬可啟動自整定，按SET鍵3秒進入儀表內層菜單，選定參數At后配合△或▽鍵開啟自整定，此時At指示燈開始閃爍儀表進入自動整定參數工作狀態，控制加熱系統在設定點附近波動二次，當At燈滅時自整定結束，新的PID參數被鎖存在芯片中。