●電池需要開機才能充電？電池需要開機按PTT才能充電？電池插座充不充，火牛重新插才能充......

我們在實際使用過程中，為了保證對講機電池的使用安全和壽命，對講機電池保護板和座充都會對電池電壓進行監控。充電過程中當檢測到電池電壓高于過充保護電壓時，自動停止充電，電池進入過充保護狀態，該保護不會馬上消除，而是需要等到電池電壓降到過充釋放電壓時才會消除。因此，會出現接近滿點的電池無法充電現象（因為此時電池還處于過充保護狀態）。

例如：過充保護電壓為4.3 ±0.05V，過充釋放電壓為4.1 ±0.05V，所以如果當你的電池電壓處于4.05V---4.3V時，電池是不充電的。

●電池不供電也不充電（外觀無鼓包、漏液等現象）

1、電池進水腐蝕：電池進水后因水電解會腐蝕器件管腳及保護板線路。

2、電池休眠：

①電池長時間未使用會因為電池自身耗電導致電池損壞無法使用；

②如果電池使用到機器自動關機后沒有將旋鈕旋至關機狀態，又沒有及時充電，此時機器部分電路還在工作需要耗電同時電池因為自身耗電而進入休眠，導致不能充電也不能放電，需要用稍高于正常充電的電壓的對電池進行充電激活，修復喚醒因自放電過深而休眠保護的鋰電池。如無可以激活的設備，可以將電池插在座充上1小時后看電池是否能激活充電。

3、電池內部連接斷開：需要返廠維修，可有萬用表檢測電池正反面觸片是否有電壓。

①一面有電壓一面無電壓：連接線異常；

②正反都無電壓：電芯鎳帶異常或者電芯已壞；

③電壓異常：單節電池電壓小于2.5v，雙電池電壓小于5V，電芯已壞或保護板器件異常（雙節電壓小于5V還有可能是其中一節電芯鎳帶脫落）。

●電池充電慢？充電時無法開機？

1、插座接觸不好會導致充電慢；

2、開機充電因機器待機耗電會導致感覺充電變慢；

3、電池電量接近完全耗盡；

如果電池耗電太深，電池電壓過低，出于對電池保護，剛開始充電時會以很小的電流充電，將電池充至一定電壓之后才會以正常充電電流充電，故整個充電過程會變長；同時如果機器是開機充電，有可能因為機器耗電電流大于充電電流而無法開機或者無法正常發射；電池電壓過低開機充電，機器可能出現頻繁重啟。

●電池不耐用？

1、確認電池實際使用電芯容量，避免虛標誤導；

2、對講機開機充電會導致電池充不滿，電池充飽后停止充電，對講機會繼續耗電，在耗到電池電壓低于過充保護釋放電壓前電池不會繼續充，導致電池其實不是滿電狀態；

3、對講機頻繁受到信號干擾，導致電池無法進入省電狀態，待機耗電加大；

4、充電或使用環境溫度越低電池放電量會越小，表現為越不耐用；

5、電池每充放電1次容量都在縮小，故使用中電池會越來越不耐用；

6、每塊電池充飽的飽和程度會有差異，導致放電量會不一樣。