一、電動液壓升降柱電機怎么接線

1、升降柱設備動力單元預留線

升降柱動力單元電機有一條三芯電纜線依次為紅色，黑色，黃色，電磁閥為兩根黑線、帶警示燈的有一條兩芯螺旋燈線，共七根線，不帶警示燈的共五根線，外筒固定鋼筋焊接完成后開始接線。

2、接線流程

把動力單元液壓一體機上面的不銹鋼面板打開，放在外筒基礎溝一側的地面上，把外筒上方引出的七芯電纜，分別接到動力單元的電機線、電磁閥線、警示燈線上。準確記清楚七芯線電纜線的線號或顏色，與設備上的電機，電磁閥、警示燈所對應的線號顏色，以免控制箱接錯線。

3、設備接線說明

路樁上電機線3根線，紅色電機上、黃色電機下、黑色線電機公用，接在控制箱所對應的端子上不可接反。電磁閥2根單獨的黑色線，接在控制箱電磁閥、電磁閥公用對應端不分正負極。警示燈線1根兩心線接在控制箱警示燈、警示燈公用端分正負極。

4、接線標準

線頭接好后要用焊錫焊接好，先用塑料膠帶纏好，再用高壓防水膠帶纏兩層，然后在用塑料膠帶纏實，然后用電工瀝青膠布纏好，一共包四次，線接好后把接線端的電線整理規范，固定在動力單元的下方，防止外力把接線處拉斷。整理好后先把動力單元上接警示燈的2根線連在一起，用萬用表測量電纜線的另一端，3根線電機是通的、2根線電磁閥是通的。2根燈線是通的，電機、電磁閥、電線之間是不可以通的，確認后剩余的電纜線，規范地放入外筒側面的儲線盒里面，每個樁接入控制箱內的對應端排上。

注意：在此要提醒大家，不同品牌的升降柱安裝流程可能會有所不同，請大家根據實際情況的品牌進行安裝接線。

二、自動升降柱停電怎么辦

當發生停電狀況時，自動升降柱是無法通過遙控器來控制路樁升降的。這時可以打開自動升降柱的控制系統，通過系統自帶的應急裝置設置來將路樁降下，方便車輛通行。控制系統上的主板紅色按鍵為下降按鈕，綠色按鍵為上升按鈕。